• Placement Questions

Placement Papers with Solutions

(#M40156898) HR INTERVIEW QUESTION Engineering Som Keep an EYE

The distance between the centres of rivets in adjacent rows of zig-zag riveted joint, is called back pitch.


A. True
B. False

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (1)   (2) Submit Your Solution

(#M40156897) HR INTERVIEW QUESTION Engineering Som Keep an EYE

The steel bars in a reinforced cement concrete beam are embedded __________ of the beam.


A. in the centre
B. near the bottom
C. near the top
D. at any position

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (7)   (1) Submit Your Solution undefined

(#M40156896) HR INTERVIEW QUESTION Engineering Som Keep an EYE

The assumption made in the theory of the reinforced cement concrete beam is that


A. all the tensile stresses are taken up by the steel reinforcement only
B. there is a sufficient bond between steel and concrete
C. the steel and concrete are stressed within its elastic limit
D. all of the above

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (1) Submit Your Solution

(#M40156895) HR INTERVIEW QUESTION Engineering Som Keep an EYE

Shear modulus is the ratio of


A. linear stress to linear strain
B. linear stress to lateral strain
C. volumetric strain to linear strain
D. shear stress to shear strain

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (1)   (0) Submit Your Solution

(#M40156894) HR INTERVIEW QUESTION Engineering Som Keep an EYE

A thick pressure vessel is always used for the generation of steam, as it can withstand high pressures.


A. True
B. False

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (0) Submit Your Solution

(#M40156893) HR INTERVIEW QUESTION Engineering Som Keep an EYE

In case of eccentrically loaded struts __________ is preferred.


A. solid section
B. hollow section
C. composite section
D. reinforced section

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (15)   (3) Submit Your Solution

(#M40156892) HR INTERVIEW QUESTION Engineering Som Keep an EYE

The Rankine's formula holds good for


A. short columns
B. long columns
C. both short and long columns
D. weak columns

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (1)   (0) Submit Your Solution

(#M40156891) HR INTERVIEW QUESTION Engineering Som Keep an EYE

The modulus of elasticity for mild steel is approximately equal to


A. 10 kN/mm2
B. 80 kN/mm2
C. 100 kN/mm2
D. 210 kN/mm2

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved Read Solution (1)

Is this Puzzle helpful?   (20)   (1) Submit Your Solution

(#M40156890) HR INTERVIEW QUESTION Engineering Som Keep an EYE

The unit of stress in S.I. units is


A. N/mm2
B. kN/mm2
C. N/m2
D. any one of these

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved Read Solution (1)

Is this Puzzle helpful?   (10)   (4) Submit Your Solution

(#M40156889) HR INTERVIEW QUESTION Engineering Som Keep an EYE

A leaf spring is supported at the


A. ends and loaded at the centre
B. centre and loaded at the ends
C. ends and loaded anywhere
D. centre and loaded anywhere

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (0) Submit Your Solution