• Placement Questions
• /
• GATE

GATE Latest Exam Pattern - GATE Sample Question with Solutions Page 11

(#M40156788) GATE QUESTION ENGINEERING SOM Keep an EYE

A localised compressive stress at the area of contact between two members is known as


A. tensile stress
B. bending stress
C. crushing stress
D. shear stress

Asked In Gate Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (3)   (0) Submit Your Solution

(#M40156787) GATE QUESTION ENGINEERING SOM Keep an EYE

The distance between the centre of a rivet hole to the nearest edge of plate, is called


A. margin
B. pitch
C. back pitch
D. diagonal pitch

Asked In Gate Jaspalsingh Parmar (9 years ago)

Unsolved Read Solution (2)

Is this Puzzle helpful?   (12)   (6) Submit Your Solution

(#M40156786) GATE QUESTION ENGINEERING SOM Keep an EYE

When a body is subjected to a direct tensile stress (σ) in one plane, then tangential or shear stress on an oblique section of the body inclined at an angle θ to the normal of the section is


A. σ sin 2θ
B. σ cos 2θ
C. σ/2 sin 2θ
D. σ/2 cos 2θ

Asked In Gate Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (1)   (0) Submit Your Solution

(#M40156785) GATE QUESTION ENGINEERING SOM Keep an EYE

A thin cylindrical shell of diameter (d), length (l) and thickness (t)is subjected to an internal pressure (p). The hoop stress in the shell is


A. pd/t
B. pd/2t
C. pd/4t
D. pd/6t

Asked In Gate Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (1)   (1) Submit Your Solution

(#M40156784) GATE QUESTION ENGINEERING SOM Keep an EYE

A square beam and a circular beam have the same length, same allowable stress and the same bending moment. The ratio of weights of the square beam to the circular beam is


A. 1/2
B. 1
C. 1/1.12
D. 1/2

Asked In Gate Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (4)   (0) Submit Your Solution

(#M40156783) GATE QUESTION ENGINEERING SOM Keep an EYE

A steel bar 2 m long, 20 mm wide and 10 mm thick is subjected to a pull of 2 kN. If the same bar is subjected to a push of 2 kN, the Poission's ratio of the bar in tension will be __________ the Poisson's ratio for the bar in compression.


A. equal to
B. less than
C. greater than

Asked In Gate Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (0) Submit Your Solution

(#M40156782) GATE QUESTION ENGINEERING SOM Keep an EYE

A pressure vessel is said to be a thick shell, when


A. it is made of thick sheets
B. the internal pressure is very high
C. the ratio of wall thickness of the vessel to its diameter is less than 1/10.
D. the ratio of wall thickness of the vessel to its diameter is greater than 1/10.

Asked In Gate Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (0) Submit Your Solution

(#M40156781) GATE QUESTION ENGINEERING SOM Keep an EYE

The neutral axis of a transverse section of a beam passes through the centre of gravity of the section and is


A. in the vertical plane
B. in the horizontal plane
C. in the same plane in which the beam bends
D. at right angle to the plane in which the beam bends

Asked In Gate Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (1)   (1) Submit Your Solution

(#M40156780) GATE QUESTION ENGINEERING SOM Keep an EYE

In the above question, the ratio of stiffness of spring 'B' to spring 'A' will be


A. 2
B. 4
C. 6
D. 8

Asked In Gate Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (1) Submit Your Solution

(#M40156779) GATE QUESTION ENGINEERING SOM Keep an EYE

A cantilever beam is one which is


A. fixed at both ends
B. fixed at one end and free at the other end
C. supported at its ends
D. supported on more than two supports

Asked In Gate Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (0) Submit Your Solution