• Placement Questions
• /
• HR INTERVIEW

HR Interview Questions and Best Answer Page 13

(#M40156832) HR INTERVIEW QUESTION Engineering som Keep an EYE

When a rectangular beam is loaded transversely, the maximum tensile stress is developed on the


A. top layer
B. bottom layer
C. neutral axis
D. every cross-section

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (12)   (5) Submit Your Solution

(#M40156831) HR INTERVIEW QUESTION Engineering som Keep an EYE

The shear force of a cantilever beam of length l and carrying a gradually varying load from zero at the free end and w per unit length at the fixed end is __________ at the fixed end.


A. zero
B. wl/4
C. wl/2
D. wl

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (0) Submit Your Solution

(#M40156830) HR INTERVIEW QUESTION Engineering som Keep an EYE

The section modulus (Z) of a beam is given by


A. I/y
B. I.y
C. y/I
D. M/I

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (0) Submit Your Solution

(#M40156829) HR INTERVIEW QUESTION Engineering som Keep an EYE

Fatigue test is carried out for


A. stresses varying between two limits of equal value, but of opposite sign
B. stresses varying between two limits of unequal value, but of opposite sign
C. stresses varying between two limits of unequal value but of same sign
D. all of the above

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (1) Submit Your Solution

(#M40156828) HR INTERVIEW QUESTION Engineering som Keep an EYE

In calculating the strength of a riveted joint in tearing, shearing and crushing, the


A. actual diameter of rivet is used
B. actual diameter of hole drilled for rivet is used
C. mean diameter of hole drilled and rivet is used
D. smaller of the rivet diameter and hole diameter is used

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (0) Submit Your Solution

(#M40156827) HR INTERVIEW QUESTION Engineering som Keep an EYE

Two solid shafts 'A' and 'B' are made of the same material. The shaft 'A' is of 50 mm diameter and shaft 'B' is of 100 mm diameter. The strength of shaft 'B' is __________ as that of shaft A.


A. one-half
B. double
C. four times
D. eight times

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (1)   (0) Submit Your Solution

(#M40156826) HR INTERVIEW QUESTION Engineering som Keep an EYE

Whenever some external system of forces acts on a body, it undergoes some deformation. As the body undergoes some deformation, it sets up some resistance to the deformation. This resistance per unit area to deformation, is called


A. strain
B. stress
C. pressure
D. modulus of elasticity

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (1)   (0) Submit Your Solution

(#M40156825) HR INTERVIEW QUESTION Engineering som Keep an EYE

The shear force diagram of a cantilever beam of length l and carrying a uniformly distributed load of w per unit length will be


A. a right angled triangle
B. an issoscles triangle
C. an equilateral triangle
D. a rectangle

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (0) Submit Your Solution

(#M40156824) HR INTERVIEW QUESTION Engineering som Keep an EYE

The value of equivalent length is taken to be half of the actual length of a column with one end fixed and the other end free.


A. Agree
B. Disagree

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (2)   (0) Submit Your Solution

(#M40156823) HR INTERVIEW QUESTION Engineering som Keep an EYE

Factor of safety is defined as the ratio of


A. ultimate stress to working stress
B. working stress to ultimate stress
C. breaking stress to ultimate stress
D. ultimate stress to breaking stress

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved Read Solution (1)

Is this Puzzle helpful?   (31)   (10) Submit Your Solution