• Placement Questions
• /
• HR INTERVIEW

HR Interview Questions and Best Answer Page 7

(#M40156892) HR INTERVIEW QUESTION Engineering Som Keep an EYE

The Rankine's formula holds good for


A. short columns
B. long columns
C. both short and long columns
D. weak columns

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (1)   (0) Submit Your Solution

(#M40156891) HR INTERVIEW QUESTION Engineering Som Keep an EYE

The modulus of elasticity for mild steel is approximately equal to


A. 10 kN/mm2
B. 80 kN/mm2
C. 100 kN/mm2
D. 210 kN/mm2

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved Read Solution (1)

Is this Puzzle helpful?   (20)   (1) Submit Your Solution

(#M40156890) HR INTERVIEW QUESTION Engineering Som Keep an EYE

The unit of stress in S.I. units is


A. N/mm2
B. kN/mm2
C. N/m2
D. any one of these

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved Read Solution (1)

Is this Puzzle helpful?   (10)   (4) Submit Your Solution

(#M40156889) HR INTERVIEW QUESTION Engineering Som Keep an EYE

A leaf spring is supported at the


A. ends and loaded at the centre
B. centre and loaded at the ends
C. ends and loaded anywhere
D. centre and loaded anywhere

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (0)   (0) Submit Your Solution

(#M40156888) HR INTERVIEW QUESTION Engineering Som Keep an EYE

A rectangular beam of length l supported at its two ends carries a central point load W. The maximum deflection occurs


A. at the ends
B. at l/3 from both ends
C. at the centre
D. none of these

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (2)   (3) Submit Your Solution

(#M40156887) HR INTERVIEW QUESTION Engineering Som Keep an EYE

For no tension condition in the base of a short column of circular section, the line of action of the load should be within a circle of diameter equal to __________ of the main circle.


A. one-half
B. one-third
C. one-fourth
D. one-eighth

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (6)   (2) Submit Your Solution

(#M40156886) HR INTERVIEW QUESTION Engineering Som Keep an EYE

When a body is subjected to a direct tensile stress (σ) in one plane, then maximum normal stress occurs at a section inclined at __________ to the normal of the section.


A. 0°
B. 30°
C. 45°
D. 90°

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (2)   (2) Submit Your Solution

(#M40156885) HR INTERVIEW QUESTION Engineering Som Keep an EYE

In case of an under-reinforced beam, the depth of actual neutral axis is __________ that of the critical neutral axis.


A. same as
B. less than
C. greater than

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (3)   (2) Submit Your Solution

(#M40156884) HR INTERVIEW QUESTION Engineering Som Keep an EYE

The tensile strength of ductile materials is __________ its compressive strength.


A. equal to
B. less than
C. greater than

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (3)   (2) Submit Your Solution

(#M40156883) HR INTERVIEW QUESTION Engineering Som Keep an EYE

The bending stress in abeam is __________ bending moment.


A. equal to
B. less than
C. more than
D. directly proportional to

Asked In HR Interview Jaspalsingh Parmar (9 years ago)

Unsolved

Is this Puzzle helpful?   (1)   (0) Submit Your Solution